Regrip Your Golf Clubs With Rubbing Alcohol | Full Guide

Replacing worn golf grips is an important part of your golf club maintenance. For those looking to save, regripping your golf clubs at home is a great way to keep expenses low. The most frugal of golfers may try to really save by using golf grip solvent alternatives such as rubbing alcohol, but is that a good idea?

Everyone wants to save money but sometimes cutting corners can cost you more in the end. A DIY regripping project only saves money in the long run if you do it correctly. Golfers are best to not cut corners while regripping their clubs to save a few dollars. That said, golf grip solvent isn’t the only solution to install golf grips. There are budget friendly alternatives.

In the article below, we are going to cover all you need to know about regripping golf grip with rubbing alcohol. We will look at if rubbing alcohol is a practical alternative to grip solvent, how to use rubbing alcohol to regrip, as well as everything else you need to know. We have a lot to cover so let’s jump in.

Should You Use Rubbing Alcohol To Install Golf Grips?

Standard golf grip solvent works in two ways. It lubricates the golf grip and golf grip tape for installation. It also helps the newly installed golf grip adhere to the golf club.

Grip solvent is excellent in performing both these tasks but it’s not the only tool for the job. While we would not recommend as our first option, you absolutely can use rubbing alcohol to install your golf grips.

For those looking to save, we would suggest not skimping on golf grip solvent. Instead, there are plenty of budget friendly golf grips that you can buy that are high quality while not breaking the bank.

Affiliate Disclosure: Buying products through the links on the site helps us fund new and better content. As an Amazon Associate, we earn from qualifying purchases. We may receive commissions for purchases made through links in this post. Thank you for your support!


Saplize Golf Grip Kit

The Saplize Golf Grip Kit offers a one stop solution for your DIY golf grip project, and it’s budget-friendly too! This kit includes 15 Golf Grip Tape Strips, Grip Solvent, a Hook Blade, and a Rubber Vise Clamp, ensuring a quick and easy grip installation. Don’t compromise on your golf grip project when this kit provides all the you need at a great value!

How To Install Golf Grips With Rubbing Alcohol

Installing golf grips with rubbing alcohol is virtually identical to installing with golf grip solvent. Follow the instructions below for a detailed, step-by-step guide.

best alternative

Rubbing Alcohol

Rubbing alcohol, a common household item, is a great alternative for golf grip solvent. Its chemical makeup is similar to standard solvent so DIYers can always use rubbing alcohol when in a pinch. However, we would always recommend using golf grip solvent when that is an option.

What You Will Need

  • New Golf Grip
  • Double Sized Golf Grip Tape
  • Utility Knife
  • Rubbing Alcohol
  • Bucket
  • Cloth For Drying

Step By Step Instructions

  1. Remove your old grip from the clubs you wish to regrip. Use a utility knife or scissors for best results. Be sure to always cut away from your body as the grip can be quite tough. Remove the leftover tape and wipe away any residue with a cloth.
  2. Measure the length of grip tape needed on the club shaft. Apply enough tape on the shaft to cover the length of the grip. Excess tape can be removed after installation. Also, make sure that the grip tape coves the diameter of the club shaft.  
  3. Cover the end of your new grip with a golf tee and pour rubbing alcohol inside it. Cover the golf grip with rubbing alcohol as well. Once the inside of the grip is smothered, slide the grip over the top of the tape and fasten it in place.
  4. Leave the grip to dry. Leave the newly gripped clubs to dry and set in a warm room in your house.  Allow at least eight hours of dry time before heading out to the course or driving range.

Can Rubbing Alcohol Damage Your Golf Clubs And Grips During Installation?

There is minimal risk in ruining your golf clubs when installing grips using soap and water. However, you do run the risk of damaging your new grips. Rubbing alcohol should work in most cases but if not properly executed, you may ruin the grip.

What Are Rubbing Alcohol Alternatives For Installing Golf Grips?

We would always recommend using golf grip solvent to regrip your clubs. It is not expensive, and it is specially formulated to adhere golf grips to newly tapped golf clubs.

If you are in a situation where you cannot find or use golf grip solvent, below are suitable alternatives.

Final Thoughts

Golf can be an expensive sport. Between the equipment and cost to play, many golfers look for ways to save. While there are ways to cut cost, we would advise against using rubbing alcohol to regrip your golf clubs. There really is now substitute better than golf grip solvent.

Regripping your golf clubs incorrectly will cause you more in the long run. Use the tips above to regrip your clubs correctly and to avoid extra costs.  

Once you regrip your new clubs, be sure to keep up with their maintenance Check out our article on 5 Easy Ways To Clean Your Golf Grips to make sure your golf grips last.

For those not up for a project, big box retailers, such as Golf GalaxyPGA Tour Superstore, and Dick’s Sporting Goods, all offer regripping services at a decent price.

Hopefully you liked this article and found it informative. Check out our other blog posts if you liked this one!

4 thoughts on “Regrip Your Golf Clubs With Rubbing Alcohol | Full Guide”

Leave a Comment